• THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING, please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us at 1-800-253-1301. You will need your model and serial number located on the front facing of the microwave oven opening, behind the door. • IMPORTANT SAFETY INSTRUCTIONS Use the microwave oven only for its intended use as described in this manual. Do not use corrosive chemicals or vapors in the microwave oven.

Download 1518 Whirlpool Microwave Oven PDF manuals. User manuals, Whirlpool Microwave oven Operating guides and Service manuals. Choose Whirlpool home appliances. Whether replacing or remodeling, our selection of online appliance options help you find the tools your household needs.

This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use. • WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Observe all governing codes and ordinances.

• Clock The Clock is a 12-hour (12:00-11:59) or 24-hour (0:00-23:59) clock. Touch OPTIONS/CLOCK to reach Clock submenu, and follow the prompts to set the Clock. Clock format (12 hours with AM and PM, 12 hours without AM and PM or 24 hours) may also be set in the Clock submenu. • Microwave-Safe Browning dish (Follow manufacturer recommendations.) Ceramic glass, glass China, earthenware (Follow manufacturer recommendations.) Melamine (Follow manufacturer recommendations.) Paper towels, paper plates, napkins (Use non-recycled paper.) Plastic wraps, bags, covers, dinnerware, containers (Follow manufacturer recommendations.) Pottery and clay (Follow manufacturer recommendations.) Silicone bakeware (Follow manufacturer recommendations.) Wax paper To Test Cookware/Dinnerware: Place dish in microwave oven with 1 cup (250 mL) of water beside it. • General Cleaning IMPORTANT: Before cleaning, make sure all controls are off and the microwave oven is cool.

Always follow label instructions on cleaning products. To avoid damage to the microwave oven caused by arcing due to soil buildup, keep cavity, microwave inlet cover, cooking rack supports, and area where the door touches the frame clean. • Charcoal filter Cooktop light bulb Cavity light bulb Troubleshooting to possibly avoid the cost of a service call.

Www.whirlpool.com Turntable alternates rotation directions This is normal and depends on motor rotation at the beginning of the cycle. Display shows messages “Enter clock”. • For additional product information or to view FAQs (Frequently Asked Questions), visit www.whirlpool.com. If you do not have access to the Internet and you need assistance using your product, you may contact Whirlpool at the number below.

Have your complete model number ready. You can find your model number and serial number on the label located on the upper or lower front facing of the microwave oven opening, behind the door.

• 30” EYE-LEVEL GAS MICROWAVE RANGE 30” EYE-LEVEL GAS RANGE IMPORTANT INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE HOMEOWNER HOMEOWNER: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Ve Ovens, Compactors, Room Air Conditioners, Dehumidifiers, Automatic Washers, Clothes Dryers, Freezers, Refrigerator-Freezers, Ice Makers,Dishwashl. • Before you begin Read these instructions completely If followed, they will simplify the installation If your range does not have a microwave disregard following oven, information. IMPORTANT: Observe all governing codes and ordinances. Essentials Of Psychology 4th Edition Stephen L Franzoisch Deutsch.

Failure to follow these instructions to fire or electrical shock hazard. From from floor. 25/,6 above the cooktop must have a of the installer with the installation clearance of base cabinet, left to avoid material from the oven cavity. The unit, check for damage such as Whirlpool trained ser. Gas supply requirements Before connecting to the supply system, be sure that the Installation conforms with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI 2223.1-l 980. These ranges are designed for easy connection tween the supply line and the inlet fitting.

Electrical requirements - Conventional Eyelevel A 120 Volt, 60 Hz, AC only, 15 Ampere fused electrical supply is required (time delay fuse or circuit breaker is recommended). It is recommended circuit serving only this appliance be provided. DO NOT use an extension cord.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY PRONG. This appliance is equipped with a power supply cord having a 3-prong grounding plug. (See Figure 5.) To minimize possible shock hazard, the cord must be plug- ed into a mating 3-prong grounding tacle, grounded in accordance with the National Elec- trical Code, ANSUNFPA. • Gas connection A. To access gas line FIG.

7 Remove storage drawer by lifting slightly and pulling out of the range. The connection is now accessible. Connect gas line TOP VIEW OF GAS SUPPLY LINE 1. The pressure regulator has a l/z” female pipe thread. It is recommended that a 115”. • gq@- - SHUTTER FIG. 9 The air shutters on the top burner manifold should be adjusted for a proper flame.

The flame should be soft in character. To adjust the air shutter, loosen the lock screw. Move the air shutter to close the opening to decrease the air or enlarge the opening for more air.

B Remove the cap with the screwdriver slot and replace upside down. This plug will then have the marking “LPGIO.” Be sure not to disturb or remove the spring beneath this plug. See Figure B for correct positioning of plug.

• The appearance of a properly adjusted gas flame is one having an inner cone of bluish-green and an outer man- tle of dark blue. The flame characteristics clean and soft. NOTE: On LP gas a slight yellow tip will be visable on top burner flames, but will not affect burner performance. • Check operation A. Surface burners 1. Push in and turn the knob to “LITE” 2. When the burner lights, turn the knob clockwise to the desired setting.

Do not leave the knob in the “LITE” position once the burner 3. If the flame should go out during the cooking opera- tion, turn burner off. • Installing optional aGIl vent hood above eyelevel micro- wave range A. Space required WITH VENT HOOD:%RALL HEIGHT EYE-LEVEL RANGE uq/-y FIG. 15 Install vent hood BEFORE making connection. When measuring, remember that leveling legs will be adjusted.

Total height needed for vent hood is 72” with legs not extended. • Loosen screws and remove the two small plates on the back of the hood. Remove the screws in the back of the oven. Remove the two Z brackets from the hardware package. Position the hood on the range one inch from the rear and align holes in brackets (one each side) with holes in the hood and in the range.

• BK-W THERMLYxSE8” FggF1 ICAWlYI 15 AMP THERMAL &---; PROTECTOR lYA0NEn?0N1 &ARY NTERLOCK nrrn ’ rlccu RELAY COIL! CONTROL MODULE L---------- NOTE SHOWS DOOR OPEN. DIAGRAM Ob5N OFF. PROBE 1 CONNECTOR Upper Oven SM958PEP LIGHT SWITCH ) MOi;TOR I SWITCH I ICI L------1 PROBE. • (MANUAL) OVEN LIGHT SW SWITCH FUSE MANIFOLD SW COLOR FLAGGING IS A COMMON YHACllCt IN ORIGINAL AND REPLACEMENT WIRING WHEN TRACING, CHECK FOR FLAGS AT EACH TERMINATION SELECTOR SWITCH SCHEDULE POSITION CONTACTS A & B OPEN BAKE TIMED BAKE BROIL A-2, B-4 NOTE WIRES TO BE REPLACED MUST HAVE. • THERMWSEBK ICAWTII THERMAL L PROTECTOR IYAONETROHI PC;;IMARY INTERLOCK TRANSFORMER CONTROL MODULE RECTIFIER’, ‘-b&’ CONNECTOR Upper Oven SM966PEP 15 AMP LIGHT:,---: SWITCH (NC)- “” $ih,, PROBE MICROCOMPUTER (CPU) ASSEMBLY MOTOR POWER TRANSFORMER ” J-----%9-?

L--------J DIO ’ OVEN LIGHT I/ MAGNETRON r-----7. LAMP SWITCH STA)i;ER OVEN LIGHT SW (MAN ) L------J TLHERM SELECTOR SW. STAT /*NO MANIFOLD SW. TERMINALS A & 1 LOCATED ON SELECTOR SWITCH NOT USED SELECTOR SWITCH SCHEDULE CONTACTS POSITION OPEN CLOSED OVEP4J”hAMP r---l r L --+-I SPARK ~H+--~~ULE Ll -HI.

• y&-r 7; J” L-,-J L--3----: THERM0 SELECTOR SW. ^-_- MANIFOLD SW Terminals A & 1 Located on Selector Switch Not Used SELECTOR SWITCH SCHEDULE CONTACTS POSITION OPEN L--e UPPER OVEN THERMOSTAT VALVE d--lHOOO OUTLET L3-_2-'J CONNECTOR h”” '--+I SPARK HV'MOOULE i-K - A-?* ‘,S. • Automatic Washers, Clothes Dryers, Freezers, Refrigerator-Freezers, Ice Makers, Dishwashers, Built-In Ovens and Surface Units, Ranges, Microwa Whirlpool HOME I b APPLIANCES Maklng your world a little easier. In the event your WHIRLPOOL appliance should appliance or a WHIRLPOOL franchised TECH-CARE@ telephone directory listed under “Appliances-Household-Major-Service name number dialing, free.